OSHA defines a PIT as “any mobile power-propelled truck used to carry, push, pull, lift, stack or tier materials.” Most people think of PITs as forklifts. Though forklifts come in many shapes and sizes, they are all regulated under OSHA’s PIT standard, 29 CFR § 1910.178. PITs also include manlifts, scissor lifts, boom lifts and motorized hand trucks. Though this article will often refer to forklifts, the requirements apply to all PITs. Earth moving and over the road haulage trucks are not included in the definition of PIT. Equipment that was designed to move earth but has been modified to accept forks are also not included.
Forklifts present many potential hazards: a pedestrian can be struck by a forklift; a load can fall off a forklift onto a person or the operator; the forklift can fall off a ledge or tip if driven on an uneven surface; a forklift can fall between a loading dock and a truck trailer. Frequently, an accident involving a forklift results in serious injury or a fatality. To address these hazards, OSHA sets out a comprehensive set of standards for training, maintenance, and operation of forklifts. OSHA also requires initial certification and recertification of forklift drivers every three years. If forklift certifications or maintenance records are falsified, OSHA has a history of seeking criminal sanctions to enforce its standards.
This article will briefly outline OSHA’s requirements for use of forklifts in the workplace and will discuss a case where an employer falsified forklift maintenance records, resulting in criminal sanctions.
OSHA’S TRAINING AND CERTIFICATION REQUIREMENTS
OSHA’s Powered Industrial Trucks Standard requires that “The employer shall ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely…” The Standard also requires that operators receive training in the topics which are applicable to the safe operation of the truck in the employer’s workplace. Employees must be trained separately for each different type of forklift they will be using, but they do not need to complete separate training for the same type of forklift made by a different manufacturer.
The Standard further requires an employer to develop a written program to train all employees who will be required and authorized to operate forklifts as to the hazards of such equipment. Employers must conduct classroom-type training and actually observe the employee operating the equipment under the physical conditions at the workplace, such as aisles, ramps, and loading docks. The employer must provide a certificate stating the employee has completed the training. The employee must be retrained and recertified every three years, at a minimum, or after an accident or “near miss” which resulted from an unsafe act.
If contract or temporary workers who are not employed by the host employer are required to operate forklifts, the host employer must take steps to assure that these individuals are properly trained before they are permitted to operate forklifts at the facility. At a minimum, the host employer is responsible for the safety of its own employees. If the operation of forklifts could endanger the host employer’s employees, the host employer would be obligated to prevent such danger by satisfying itself that all forklift operators have been properly trained. This does not mean that a host employer is required to train forklift drivers who are not its employees. It must, however, ensure that such individuals have been trained in accordance with the PIT standard before they are permitted to operate forklifts at its workplace.
Because OSHA takes training requirements so seriously, it is a good practice that all contract and temporary employees be trained and certified by the host employer before being allowed to operate a forklift, even if they received training and certification from another employer. In addition, the host employer should obtain the training and certification documentation from the contract or temporary staffing service company to confirm that it exists and is current if it intends to rely upon it and before allowing the contract or temporary worker to operate the PIT.
The PIT Standard does not specify how long training certifications must be retained after the initial certification or the recertification required every three years or after a “near miss”. Some employers retain the training certifications for the duration of employment for each employee.
If OSHA can establish that training was not provided or that the employees did not understand it because the training is in writing and the employee is illiterate or the training was conducted verbally in a language the employee could not understand, the agency may claim that the certifications are false, resulting in citations or potential criminal liability for the individual who signed the certification as well as the employer.
MAINTENANCE AND INSPECTION REQUIREMENTS
OSHA prohibits operation of forklifts if they are not in safe operating condition. It is recommended that employers conduct an inspection of each forklift at the beginning of each shift and after any maintenance has been done or an accident has occurred. At a minimum, forklifts are required to be inspected daily. While not required, the employer should consider developing and using a written daily checklist to confirm that the operator conducted the daily PIT inspection. The checklists should be reviewed periodically to assure that they are being utilized. In addition, is a best practice to maintain inspection and maintenance records for at least the duration of the time they own the specific forklift. For a detailed inspection checklist for a PIT see OSHA’s checklist.
The PIT Standard lists a number of conditions under which a forklift must be removed from service. If the operator notes these conditions while driving, the operator must stop, park the vehicle and get assistance:
- If the forklift is not in safe operating condition.
- If the forklift emits hazardous sparks or flames from the exhaust system.
- If the temperature of any part of any forklift is found to be in excess of its normal operating temperature.
- If the forklift has a leak in the fuel system.
If there is a question regarding the safe operation of a forklift, the vehicle must be immediately removed from service until it can be thoroughly inspected and any repairs are made. Similar to falsification of employee training certifications, any falsification of inspection or maintenance records can result in citation by OSHA and possible criminal liability.
The employer must also consider whether the forklift is properly rated to be operated in certain workplace environments, for example, is it rated to operate in an area where flammable or combustible materials are being utilized or stored, to insure that the forklift does not create a source of ignition for flammable or combustible materials.
OPERATOR FITNESS AND DISCIPLINE
As employers should know, there is a duty to enforce compliance with the PIT regulation with discipline for violations, including unsafe operation, failure to inspect, etc. This discipline needs to be in writing in order to remove a non-compliant operator and also to be able to establish the unavoidable employee misconduct defense to a citation. Finally, the employer must monitor whether an operator is fit to operate a PIT because of physical conditions, including vision, hearing and motor skills if there is objective evidence that these conditions are rendering the operator unfit to operate the equipment in a safe manner. In making this determination, the employer must consider the requirements of the Americans with Disabilities Act regarding assessment of the operator’s ability to perform the essential functions of the job.
In addition, the employer needs to be observant as to whether the operator is impaired by drugs or alcohol. This can be done by training supervisors on the objective signs of drug or alcohol impairment including speech, coordination, bodily odors, etc. If they are observed, the operator should be taken out of service and the employer should consider sending the employee to be tested for drugs or alcohol. Further, if there has been an accident involving personal injury or property damage, the employer should consider a post-accident drug and alcohol test. In either event, the employer should consider establishing a written drug and alcohol testing policy to be able to ensure that the operator is not impaired and creating a safety hazard.
FORKLIFT HAZARDS CREATE CRIMINAL LIABILITY
As previously mentioned, OSHA will seek criminal prosecution if an employer falsifies employee training certifications, inspection records, or maintenance records. In United States v. Atlantic States Cast Iron Pipe Company, No. 03-852, 2007 WL 2282514 (D.N.J. Aug. 2, 2007) aff’d sub nom. United States v. Maury, 695 F.3d 227 (3d Cir. 2012), the conviction of an employer on multiple criminal counts involving EPA and OSHA violations demonstrates how an employer can be exposed to this liability for a conspiracy to defraud OSHA during an inspection.
In Atlantic States, the employer was indicted for defrauding OSHA by altering existing conditions at the employer’s foundry to conceal safety hazards to which employees were exposed. In March 2000, an employee died after he was run over by the employer’s forklift. In the indictment, the government charged that the employer ignored hazards involving forklifts, including brake problems and allowing untrained employees to operate the forklifts.
In addition, after the fatality, the employer took action to deliberately conceal what had occurred from OSHA (perhaps to avoid OSHA citations). The concealment was alleged to include:
repairing the forklift brakes after the accident but shortly before OSHA commenced its inspection (after a workplace fatality OSHA must be notified within eight (8) hours and the accident scene cannot be disturbed until the OSHA inspector has an opportunity to commence the inspection and releases the scene).
Conducting a demonstration of the forklift for the compliance officer that was misleading (since the brakes had been surreptitiously repaired after the accident but before the inspector arrived).
Instructing employees to provide false information to the inspector as to how the fatality occurred.
Creating a false written inspection report after the accident which indicated that the forklift had been inspected prior to the accident and was in “perfect operating condition.”
As a result of its inspection, OSHA identified employees who were willing to testify against the employer as to the foregoing actions, resulting in felony convictions. It is important to note that if the employer had not engaged in these post-accident wrongdoings and OSHA had decided to proceed with its limited criminal prosecution authority under the Act, the employer’s liability would have likely been limited to a misdemeanor; the concealment resulted in much greater liability than the underlying violation.
CONCLUSIONS AND RECOMMENDATIONS
The Powered Industrial Truck Standard is not the most complex or the longest of the OSHA Standards. However, the requirements contained in the PIT standard are often the subject of OSHA Citations and can expose an employer to potential criminal liability if they are not followed. If your company owns a forklift, or any other type of PIT, take a look at your program to ensure all of OSHA’s requirements are satisfied: training and certification of employees, inspection and maintenance of PITs, and accurate recordkeeping. OSHA is not shy about making sure employers follow the PIT Standard; stay one step ahead of OSHA and make sure you are following the rules.